Optimasi Hidrolika Sumur X Lapangan Bunyu Kalimantan Timur dengan Metode Bit Hydraulic Impact

Sri Haryono, Wira Widyawidura

Sari


Bunyu Field placed on the Tarakan Basin, which is one hydrocarbon basins area of East Kalimantan. Formation that penetrated by the drill bit consist of sandstone, siltstone, clay stone and coal. Therefore, we need to rearrange the drilling mud system particularly on drilling mud hydraulics system. This study aims to optimize the hydraulic system in the process of drilling for wells X Fields Bunyu using bit hydraulic impact (BHI) method. The output of this method are to determine the optimum BHI fluid flow rate, penetrating power, nozzle size, and compare these parameters with the actual drill data before optimization (actual data) so that the penetration of the formation process is also optimal.  Based on actual data of well drilling there are four (4) point penetration depth (from total 13 (thirteen) point) should be optimized particularly on drilling hydraulics system by changing the size of the aperture area on the drill nozzle in accordance with the calculation using BHI method

Teks Lengkap:

PDF

Referensi


Al-Kayiem, H. H., Zaki, N. M., Asyraf, M. Z., & Elfeel, M. E. (2010). Simulation of the Cuttings Cleaning During the Drilling Operation. American Journal of Applied Sciences, 7(6), 800–806.

Coussot, P., Bertrand, F., & Herzhaft, B. (2004). Rheological Behavior of Drilling Muds , Characterization Using MRI Visualization. Oil & Gas Science and Technology – Rev. IFP, 59(1), 23–29.

Guan, Z., Liu, Y., Li, Q., Xu, Y., & Pang, H. (2015). Drilling Hydraulic Parameters Design Method under the Limited Circulating System Bearing Capacity Condition. Journal of Applied Science and Engineering, 18(3), 303–308.

http://doi.org/10.6180/jase.2015.18.3.11

Kelessidis, V. C., Dalamarinis, P., & Maglione, R. (2011). Experimental study and predictions of pressure losses of fl uids modeled as Herschel – Bulkley in concentric and eccentric annuli in laminar, transitional and turbulent fl ows. Journal of Petroleum Science and Engineering, 77, 305–312.

http://doi.org/10.1016/j.petrol.2011.04.004

Miguez, L., & Janeiro, R. De. (2011). Hydraulic Study of Drilling Fluid Flow in Circular and Annular Tubes. Brazilian Journal of Petroleum and Gas, 5(4), 239–253. http://doi.org/10.5419/bjpg2011-0023

Noah, A. Z. (2013). Optimizing Drilling Fluid Properties and Flow Rates for Effective Hole Cleaning at High-Angle and Horizontal Wells. Journal of Applied Sciences Research, 9(1), 705–718.

Paiaman, A. M., Al-askari, M. K. G., Salmani, B., & Masihi, M. (2006). Effect of Drilling Fluid Properties on Rate of Penetration. NAFTA, 60(3), 129–134.

Saasen, A., & Løklingholm, G. (2002). The Effect of Drilling Fluid Rheological Properties on Hole Cleaning. In IADC / SPE 74558 Drilling Conference (pp. 1–5). Texas.

Samsuri, A., & Hamzah, A. (2011). Water based mud lifting capacity improvement by multiwall carbon nanotubes additive. Journal of Petroleum and Gas Engineering, 2(5), 99–107.

Wittig, V., Bracke, R., & Hyun-ick, Y. (2015). Hydraulic DTH Fluid / Mud Hammers with Recirculation Capabilities to Improve ROP and Hole Cleaning For Deep , Hard Rock Geothermal Drilling. In Proceedings World Geothermal Congress 2015 (pp. 19–25).


Refbacks

  • Saat ini tidak ada refbacks.


Jurnal Mekanika dan Sistem Termal (ISSN : 2527-3841 ; e-ISSN : 2527-4910) diterbitkan oleh Universitas Janabadra dan telah terindeks oleh : Google Scholar

 

Free counters!